B52-RGB-070G12-W8 is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces. It is covered by water-resistant Parylene protective film (10um on IP65 version and 25um on IP67 version). ATTENTION: the parylene strips cannot be exposed to direct sunlight. The ultraviolet rays rapidly damage the protection.

Tech specs:

• 3838 LED
• Lumens: 500 lm/m
• Efficiency: 40 lm/W
• Strip LED colour temperature: RGB
• Power consumption 13,3 W/m (66,5W), 24V (+0%, -15%)
• Dimmable LED strip with 350 leds (70 leds/m)
• Led strip cuttable every 7 leds (every 10cm). Length 5 m, external width 8 mm, height 2 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +45°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

The F52-R30s-056922 led strip produced with two different leds: a white 2835 Honglitronic led, version HL-A-2835H421W-S1-08-HR3 for a good lighting and a 3535 RGB led for colour changing effects. In this way, you can use two different functions by installing only one led strip. The colour temperature of white led has a very narrow range between 3000K 3step.

The led strip F52-R30s-056922 is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• Strip LED colour temperature: 3000K 3step + RGB
• Lumens white 3000K: 660 lm/m
• Efficiency white 3000K: 180 lm/W
• Dimmable LED strip with 28+28 leds/m.
• Power consumption RGB led + monochrome led 5,75 W/m + 5,75 W/m (57,5W), 24V (+0%, -15%),
• Led strip cutting points every 14 leds (every 25cm). Length 5000 m, width 12 mm, height 2,5 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +50°C

K252-400-296ORH is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces. Thanks to the coating that covers the LEDs, the COB strip allows to create a dot free light with a wide beam angle.

Tech specs:

• Lumens: 990 lm/m
• Efficiency: 95 lm/W
• Strip LED colour temperature: 4000K
• Power consumption 11 W/m (275W), 230V (+0%, -15%)
• Dimmable LED strip with 7400 chips (296 chips/m)
• Led strip cuttable every 37 chips (every 12,5cm). Length 25 m, width 10 mm, height 5 mm
• Silicon colour: Transparent
• Double sided adhesive tape type: 3M 9495LE
• Working temperature: -10°C ~ +45°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

K252-300-296ORH is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces. Thanks to the coating that covers the LEDs, the COB strip allows to create a dot free light with a wide beam angle.

Tech specs:

• Lumens: 935 lm/m
• Efficiency: 90 lm/W
• Strip LED colour temperature: 3000K
• Power consumption 11 W/m (275W), 230V (+0%, -15%)
• Dimmable LED strip with 7400 chips (296 chips/m)
• Led strip cuttable every 37 chips (every 12,5cm). Length 25 m, width 10 mm, height 4,5 mm
• Silicon colour: Transparent
• Double sided adhesive tape type: 3M 9495LE
• Working temperature: -10°C ~ +45°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

LA2-870W-264N12 is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces.

Tech specs:

• Lumens: 1230 lm/m
• Efficiency: 110 lm/W
• Strip LED colour temperature: 8700K
• Power consumption 12 W/m (120W), 24V (+0%, -15%)
• Dimmable LED strip with 2640 leds (264 leds/m)
• Led strip cuttable every 8 leds (every 3,03cm). Length 10 m, external width 10 mm, height 5 mm
• Silicon colour: White
• Double sided adhesive tape type: Nano Double-Sided Tape
• Working temperature: -10°C ~ +50°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

L52-ORAW-264N12 is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces.

Tech specs:

• Strip LED colour temperature: Orange
• Power consumption 12 W/m (60W), 24V (+0%, -15%)
• Dimmable LED strip with 1320 leds (264 leds/m)
• Led strip cuttable every 8 leds (every 3,03cm). Length 5 m, external width 10 mm, height 5 mm
• Silicon colour: White
• Double sided adhesive tape type: Nano Double-Sided Tape
• Working temperature: -10°C ~ +50°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

L52-BLUW-264N12 is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces.

Tech specs:

• Strip LED colour temperature: 460-465nm
• Power consumption 12 W/m (60W), 24V (+0%, -15%)
• Dimmable LED strip with 1320 leds (264 leds/m)
• Led strip cuttable every 8 leds (every 3,03cm). Length 5 m, external width 10 mm, height 5 mm
• Silicon colour: White
• Double sided adhesive tape type: Nano Double-Sided Tape
• Working temperature: -10°C ~ +50°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

LED Strip made of COB LED chips that incorporate a controller WS2811 inside. These strips can be used only with the specific controllers.

LED control strips (also known as RGBIC) are controllable on a pixel-by-pixel basis using dedicated controllers. A pixel corresponds to the single cut of the strip.

The led strip F52-CoRGB-720OR2 is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• COB LED
• Control chip: WS2811
• Pixels per meter: 20
• Strip LED colour temperature: RGB
• Power consumption 19 W/m (95W), 24V (+0%, -15%)
• Dimmable LED strip with 3600 chips (720 chips/m)
• Led strip cuttable every 36 chips (every 5cm). Length 5 m, width 10 mm, height 2 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +45°C

L52-GLDW-264N12 is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces.

Tech specs:

• Strip LED colour temperature: Golden Yellow
• Power consumption 12 W/m (60W), 24V (+0%, -15%)
• Dimmable LED strip with 1320 leds (264 leds/m)
• Led strip cuttable every 8 leds (every 3,03cm). Length 5 m, external width 10 mm, height 5 mm
• Silicon colour: White
• Double sided adhesive tape type: Nano Double-Sided Tape
• Working temperature: -10°C ~ +50°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

L52-LEMW-264N12 is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces.

Tech specs:

• Strip LED colour temperature: Lemon Yellow
• Power consumption 12 W/m (60W), 24V (+0%, -15%)
• Dimmable LED strip with 1320 leds (264 leds/m)
• Led strip cuttable every 8 leds (every 3,03cm). Length 5 m, external width 10 mm, height 5 mm
• Silicon colour: White
• Double sided adhesive tape type: Nano Double-Sided Tape
• Working temperature: -10°C ~ +50°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

The F52-R30s-140H12 led strip produced with two different leds: a white 2835 led for a good lighting and a RGB led for colour changing effects. In this way, you can use two different functions by installing only one led strip. The colour temperature of white led has a very narrow range.

The led strip F52-R30s-140H12 is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• Strip LED colour temperature: 3000K 3step + RGB
• Lumens white 3000K: 1660 lm/m
• Efficiency white 3000K: 125 lm/W
• Dimmable LED strip with 70+70 leds/m.
• Power consumption RGB led + monochrome led 14,4 W/m + 14,4 W/m (144W), 24V (+0%, -15%),
• Led strip cutting points every 14 leds (every 10cm). Length 5000 m, width 12 mm, height 2 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +50°C

The K52-R30s-140H12 led strip produced with two different leds: a white 2835 led for a good lighting and a RGB led for colour changing effects. In this way, you can use two different functions by installing only one led strip.

The led strip K52-R30s-140H12 is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• Strip LED colour temperature: 3000K 3step + RGB
• Lumens white 3000K: 1660 lm/m
• Efficiency white 3000K: 125 lm/W
• Dimmable LED strip with 70+70 leds/m.
• Power consumption RGB led + monochrome led 14,4 W/m + 14,4 W/m (144W), 24V (+0%, -15%),
• Led strip cutting points every 14 leds (every 10cm). Length 5000 m, width 14 mm, height 5,5 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 5604A VHB
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +50°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.