Flexible LED strip with double sided tape for a fast installation even on curved surfaces. Thanks to the coating that covers the LEDs, the COB strip allows to create a dot free light with a wide beam angle.

Tech specs:

• Lumens: 750 lm/m
• Efficiency: 95 lm/W
• Strip LED colour temperature: 3000K
• Power consumption 9,6 W/m (48W), 24V (+0%, -15%)
• Dimmable LED strip with 1600 chips (320 chips/m)
• Led strip cuttable every 16 chips (every 5cm). Length 5 m, width 10 mm, height 5 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +45°C

LED strip designed for horticulture. Due to its own spectrum of wave length this strip is suitable for stimulating the planth growth in indoor crops and hydroponic cultivation. It is not recommended to operate the 3 channels at full power unless a suitable aluminium profile is used, i.e. with a sufficiently large surface area to adequately dissipate heat. Failure to do so could result in a sharp decrease in the life of the LED in terms of hours. The led strip B52-30RB-2048O2 is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• 2835 LED
• Led/cut point: 1) Red+Blue+Warm white: 34 2) Red: 10 3) Blue: 8 4) Warm white: 16
• LED colour temperature: 1) Red: 640nm 2) Blue: 450nm 3) Warm white: 3000K
• Dimmable LED strip with 1020 leds (204 leds/m)
• Input voltage: 24V (+0%, -15%)
• Power consumption: 1) Red+Blue+Warm white: 28,8W 2) Red: 7,2W 3) Blue: 7,2W 4) Warm white: 14,4W
• Led strip cuttable every 34 leds (every 16,67cm). Length 5 m, width 12 mm, height 1,5 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• Photosynthetic Photon Flux (PPF): 1) Red+Blue+Warm white: 52,5 umol/s 2) Red: 12,4 umol/s 3) Blue: 14,2 umol/s 4) Warm white: 29,1 umol/s
• PRF: 1) Red+Blue+Warm white: 9,7 mW 2) Red: 2,1 mW 3) Blue: 2,8 mW 4) Warm white: 5,4 mW
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +45°C

Led strip was built with Honglitronic leds, version HL-A-2835H421W-S1-08-HR5. A of colour temperature 2700-6200K ensures colour stability even for different lots. For further information please consult LED datasheet.

The led strip F52-CCT-256824A-C90 is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• 2835 LED
• Lumens warm white 2700K: 2400 lm/m
• Lumens cool white 6200K: 2660 lm/m
• Efficiency warm white 2700K: 120 lm/W
• Efficiency cool white 6200K: 135 lm/W
• Strip LED colour temperature: 2700-6200K
• Power consumption 26 W/m (130W). Real power without CCT controller 52 W/m (260W). Input voltage 48 volt (+0%, -15%)
• Dimmable LED strip with 1280 leds (128+128 leds/m)
• Led strip cuttable every 32 leds (every 12,5cm). Length 5 m, width 12 mm, height 1,5 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +50°C
• IEC/TR 62778:2014 photobiological risk certificate: risk Group 1 when used as light source.

Led strip was built with Honglitronic leds, version HL-A-2835H421W-S1-08-HR5. A of colour temperature 3000-5000K ensures colour stability even for different lots. For further information please consult LED datasheet.

The led strip F52-CCT35-256824A-C9 is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• 2835 LED
• Lumens warm white 3000K: 2320 lm/m
• Lumens cool white 5100K: 2580 lm/m
• Efficiency warm white 3000K: 120 lm/W
• Efficiency cool white 5100K: 130 lm/W
• Strip LED colour temperature: 3000-5000K
• Power consumption 22 W/m (110W). Real power without CCT controller 44 W/m (220W). Input voltage 48 volt (+0%, -15%)
• Dimmable LED strip with 1280 leds (128+128 leds/m)
• Led strip cuttable every 32 leds (every 12,5cm). Length 5 m, width 12 mm, height 1,5 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 50 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +50°C
• IEC/TR 62778:2014 photobiological risk certificate: risk Group 1 when used as light source.

Led strip was built with Honglitronic leds, version HL-AM-2835H421W-S1-08-HR3-3SDCM. A of colour temperature 3000-5000K ensures colour stability even for different lots. For further information please consult LED datasheet.

The led strip F52-CCT35-2568U4A is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• 2835 LED
• Lumens warm white 3000K: 1800 lm/m
• Lumens cool white 5000K: 2810 lm/m
• Efficiency warm white 3000K: 105 lm/W
• Efficiency cool white 5000K: 135 lm/W
• Strip LED colour temperature: 3000-5000K
• Power consumption 26 W/m (130W). Real power without CCT controller 52 W/m (260W). Input voltage 48 volt (+0%, -15%)
• Dimmable LED strip with 1280 leds (128+128 leds/m)
• Led strip cuttable every 32 leds (every 12,5cm). Length 5 m, width 10 mm, height 1,5 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +50°C
• IEC/TR 62778:2014 photobiological risk certificate: risk Group 1 when used as light source.

K502-300-296ORH is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces. Thanks to the coating that covers the LEDs, the COB strip allows to create a dot free light with a wide beam angle.

Tech specs:

• Lumens: 935 lm/m (estimated value)
• Efficiency: 70 lm/W
• Strip LED colour temperature: 3000K
• Power consumption 11 W/m (550W), 230V (+0%, -15%)
• Dimmable LED strip with 14800 chips (296 chips/m)
• Led strip cuttable every 37 chips (every 12,5cm). Length 50 m, width 10 mm, height 4,5 mm
• Silicon colour: Transparent
• Double sided adhesive tape type: 3M 9495LE
• Working temperature: -10°C ~ +45°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

LED strip featuring one warm white circadian violet LED chip and one high CRI cool white LED with light spectrum similar to sun. The colour temperature range is 2700-5000K to ensure the same colour even in different batches of production.

The led strip F52-CCT-2568U4A is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• 2835 LED
• Lumens warm white 2700K: 2400 lm/m
• Lumens cool white 5000K: 3000 lm/m
• Efficiency warm white 2700K: 100 lm/W
• Efficiency cool white 5000K: 130 lm/W
• Strip LED colour temperature: 2700-5000K
• Power consumption 26 W/m (130W). Real power without CCT controller 52 W/m (260W). Input voltage 48 volt (+0%, -15%)
• Dimmable LED strip with 1280 leds (128+128 leds/m)
• Led strip cuttable every 32 leds (every 12,5cm). Length 5 m, width 12 mm, height 1,5 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 10 cm power input cables on both sides of the strip
• IEC/TR 62778:2014 photobiological risk certificate: risk Group 1 when used as light source.
• Working temperature: -10°C ~ +45°C

K502-400-296ORH is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces. Thanks to the coating that covers the LEDs, the COB strip allows to create a dot free light with a wide beam angle.

Tech specs:

• Lumens: 990 lm/m (estimated value)
• Efficiency: 70 lm/W
• Strip LED colour temperature: 4000K
• Power consumption 11 W/m (550W), 230V (+0%, -15%)
• Dimmable LED strip with 14800 chips (296 chips/m)
• Led strip cuttable every 37 chips (every 12,5cm). Length 50 m, width 10 mm, height 4,5 mm
• Silicon colour: Transparent
• Double sided adhesive tape type: 3M 9495LE
• Working temperature: -10°C ~ +45°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

LED Strip made of 2835 LED chips that incorporate a controller WS2811 inside. These strips can be used only with the specific controllers.

LED control strips are controllable on a pixel-by-pixel basis using dedicated controllers. A pixel corresponds to the single cut of the strip.

The led strip F52-Co300-120812 is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• 2835 LED
• Lumens: 1060 lm/m
• Efficiency: 100 lm/W
• Control chip: WS2811
• Pixels per meter: 20
• Strip LED colour temperature: 3000K 3step
• Power consumption 14,4 W/m (72W), 24V (+0%, -15%)
• Dimmable LED strip with 600 chips (120 chips/m)
• Led strip cuttable every 6 chips (every 5cm). Length 5 m, width 10 mm, height 2 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +45°C

LED Strip made of 2835 LED chips that incorporate a controller 1903 inside. These strips can be used only with the specific controllers.

LED control strips are controllable on a pixel-by-pixel basis using dedicated controllers. A pixel corresponds to the single cut of the strip.

The led strip F52-CoCCT-120812 is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• 2835 LED
• Control chip: 1903
• Pixels per meter: 20
• Strip LED colour temperature: 3000-6500K
• Power consumption 7,5 W/m (37,5W). Real power without CCT controller 15 W/m (75W). Input voltage 24 volt (+0%, -15%)
• Dimmable LED strip with 600 chips (120 chips/m)
• Led strip cuttable every 6 chips (every 5cm). Length 5 m, width 10 mm, height 2 mm
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• 10 cm power input cables on both sides of the strip
• Working temperature: -10°C ~ +45°C

M52-400-240D22 is a flexible waterproof led strip with 3M self-adhesive on its back side for quick installation even on curve surfaces.

Tech specs:

• Lumens: 1750 lm/m
• Efficiency: 85 lm/W
• Strip LED colour temperature: 4000K
• Led colour temperature: 4000K
• Power consumption 19,2 W/m (96W), 24V (+0%, -15%)
• Dimmable LED strip with 1200 leds (240 leds/m)
• Led strip cuttable every 6 leds (every 2,5cm). Length 5 m, width 10 mm, height 2,5 mm
• Water protection: IP53 (known as IP65 in the commercial field)
• PCB colour: White
• Double sided adhesive tape type: 3M 9495LE
• Working temperature: -10°C ~ +50°C

The energetic class refers to the light source installed inside. The luminous flux is lower and depends on the kind of IP protection.

The led strip K252-RGB-0968ZH is flexible and features a double-sided tape on its back side for quick installation even on curved surfaces.

Tech specs:

• 2835 LED
• Lumens: 235 lm/m
• Efficiency: 25 lm/W
• Strip LED colour temperature: RGB
• Power consumption 11 W/m (275W), 230V (+0%, -15%)
• LED strip with 2400 led (96 led/m)
• Led strip cuttable every 48 leds (every 50cm). Length 25 m, width 12 mm, height 5 mm
• PCB colour: Transparent
• Double sided adhesive tape type: 3M 9495LE
• Working temperature: -10°C ~ +50°C

For a perfect adhesion of the double-sided tape the temperature both of the LED strip and the surface where it is installed should be between 21 and 38°C. The LED strip will be totally fixed after 72 hours approximately. The double-sided adhesive does not guarantee a seal on painted surfaces.

WARNING: STRIP FOR OUTDOOR USE. 230V strips are subject to flickering as they are powered directly from the network voltage.